Video Upload 626 Indexing ON edited 1120

Welcome to the Inspecting and Cleaning the chapter probes, Wash Stations and Mixer Impellers on the Itelica CI Analyzer video. This procedure should be completed as part of monthly maintenance. To begin, navigate to Maintenance, set the frequency filter to Monthly, and then select Inspecting and Cleaning. The chapter Probes, Probe Wash Stations, and Mixer Impellers. Select Perform and then OK. To access online help instructions on how to perform the cleaning, select the Procedure Details button. Select OK at the prompt to allow the analyzer to enter diagnostic mode. Wait for the analyzer to enter diagnostic mode. When this message displays, the system is in diagnostic mode. Note that when the system is in diagnostics mode, the analyzer will be read in the system status map. Continue with the following steps to clean the chapter, probes, wash stations, and mixer. Wait until you have completed the cleaning and then select OK Lift up and remove the Back right cover to temporarily store the right back cover. You can hang the cover on the back of the system by positioning the cover tabs so they fit into the slots at the bottom of the opening. Locate the three chapter probes, the dilution probe, the sample probe, and the reagent probe. To protect the CHQ vets from debris, cover the Q vets with lint free tissues. To inspect the exterior of each probe, manually raise and hold the probe up with one hand until the tip is clear of the parking port. Inspect the exterior of the probe and replace if damaged. If appropriate, wipe off any debris from each probe with an alcohol pad or lint free tissue dampened with alcohol. Using the other hand, locate the probe wash station for each probe. Inspect each of the wash stations. If appropriate, wipe off and remove any debris in the wash station with an alcohol pad or lint free tissue dampened with alcohol. Locate the two chapter mixers, the reaction ring mixer and the dilution ring mixer. Inspect the exterior of each mixer impeller. If appropriate, wipe off any debris from each mixer impeller with an alcohol pad or lint free tissue dampened with alcohol. Remove the lint free tissues over the cuvettes. Reinstall the right back cover, line up the bottom of the cover with the notches on the analyzer manifold, and then push the cover in place at the top so the latches are secure. Upon completion of the maintenance task, select OK. At the prompt, there is an option to either perform additional manual maintenance activities or to resume the system. To perform additional manual maintenance activities, select Yes. To exit and resume the system, select No. This completes the procedure for inspecting and cleaning the chapter probes, wash stations, and mixer impellers on the Itelica CI Analyzer.

27 28 10 12 15 16 14 17 18 19 20 21 22 23 26 29 30 11 25 24 13 4/29/2022 4/28/2022 4/14/2022 10941300 Inspecting and Cleaning the CH Probes, Wash Stations, and Mixer Impellers on the Atellica® CI Analyzer Video SIEMENS LabManager Samples Inprocess Racks Processed Racks Troubleshooting AF030671 System DL 11:15 AM 10:46 AM Current Status Day Needs Tools 11:14 AM 10:43 AM STAT Sample Interventions Supply Needs Assay Evaluation 11:13 AM 10:41 AM 10:36 AM 1 Inprocess Reagent Needs Orders Intervention Needed 10:31 AM Patient (non-STAT) 9:31 AM Maintenance QC Statistics Calibration Due Assay Status QC Scheduler AF030680 9:27 AM 8:46 AM Inprocess: CH-02 QC Needs Gulded Workflows 3 Warnings 8:37 AM 8:06 AM Load STAT Rack Clear All Racks SESIEM-4K62FL Wednesday, 13th April 2022 Filter: View By Day Week Month Module Activity Frequency HYDRA1 Inspecting the CH Cuvettes Monthly Due Order By Count Weekly Inspecting and Cleaning the CH Probes, Probe Wash S ... April 2022 Cleaning the Cl Fan Filters Thursday Saturday %Replacing CH Reaction Cuvette Segments Cleaning Exterior of the IM Aspirate Probes Replacing the CH Source Lamp Cleaning IM Probe Rinse Stations Replacing CH Dilution Cuvette Segments Activity Type Cancel an AutoStart All Activities Related Review and Approve Maintenance Log Sunday Filter: Frequency : Monthly > Maintenance Activity Details Freque Description Inspecting and Cleaning the CH Probes, Probe Wash Stations, and Mixer Procedure Details Impellers Due Activity due: 12:00:00 AM. Performed by Operator Scheduled Date Time or Counts 06/03/2022 12:00:00 AM Performed by Operator Started Date Time or Counts First Friday of the month at 12:00 AM Number of Cycles (Count) Approved By Actions Perform Postpone Not Performed OK Cancel Wednesday Thursday Friday ? QAE Filter: Freque Frequency : Monthly X Insp i Perform manual activity at HYDRA1 This switches the module into Diagnostic Mode and prepares the module to perform the manual activity. This operation will take several minutes and the module will not be available for sample processing. Rep To continue "Inspecting and Cleaning the CH Probes, Probe Wash Stations, and Mixer Impellers", select OK. To cancel this operation, select Cancel Clea CSE No Filter Last Performed HY003722 HY003722133 Inspecting and Cleaning the CH Probes, Probe Wash Stations, and Mixer Impellers Mark as Completed Perform manual activity for HY003722 Activity Status Inspecting and Cleaning CH Probes. Probe Wash Stations, Mixer Impellers. See Instructions for Use, When complete, select OK Close Replacing CH Reaction Cuvette Segments Replacing CH Reaction Washer Probe 1 Monday Do not remove the probes while cleaning. Filter Use. When complete, select OK Activity completed. Do you want to perform additional manual maintenance activities? To perform additional manual activities, select Yes. To exit and resume module, select No Yes No Impellers activity is automatically marked as completed in the software. Disclaimer Please note that the learning material is for training purposes only. For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively "Operator Manual") issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Please note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively "Functionality") may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Siemens Healthcare GmbH 2023 91052 Erlangen, GermanylTelephone: +49 9131 84-Olsiemens-healthineers.com